+ Reply to Thread
Page 3 of 6 FirstFirst 1 2 3 4 5 ... LastLast
Results 21 to 30 of 56

Thread: 380 key

  1. #21
    chrisv's Avatar
    Join Date
    Jun 2009
    Location
    South Australia
    Posts
    1,044

    Default

    Brilliant

  2. #22
    380matey's Avatar
    Join Date
    Jul 2009
    Location
    New South Wales
    Posts
    1,001

    Default

    Does anyone know if you can use a universal remote for this or does it have to be the mega $$$ mitsi one?

  3. #23
    380VRX's Avatar
    Join Date
    Feb 2009
    Location
    New South Wales
    Posts
    24

    Default

    I work at Pickles, I have a 380 SX without a key (Repo job). I got a quote to get a key for it and programmed etc $322 (I think, the details are at work) and i also had to get it towed there. That was the price for 1 key from a Mitsubishi Dealer. I should be getting the car back tomorrow and I'll let you know of the full cost, but I know it's under $350

  4. #24
    wannamagna's Avatar
    Join Date
    Sep 2006
    Location
    Western Australia
    Posts
    213

    Default

    Quote Originally Posted by Sidewinder42 View Post
    OK, before you read these, please note THESE INSTRUCTIONS ARE UNTESTED!!


    1) First find the DLC plug (inside under driver side, right hand side, next to transmission wall). Itís a 16 pin connector with pins 1-8 on the wide side, 9-16 on the narrow side. Look closely and you can see the number 8, and barely make out the number 1.

    2) Insert a paper clip into pin 1 and another into pin 4. Run two clip on wires up to where you can work comfortably so you can jumper 1 & 4 together in the next steps.

    3) Insert your key into the ignition. Do not turn it. Just put it in.

    4) Jumper 1&4. Within 10 seconds press the hazard button 6 times (thatís 3 on & 3 off). Your doors should lock and unlock to confirm registration mode.

    5) Press and release the lock button of your 1st remote once.

    6) Within 10 seconds of step 5 press and release the lock button of your remote TWICE.

    7) The doors should lock and unlock to confirm registration.

    8) If registering additional remotes follow steps 5 -7 again for up to a total of 4 remotes. But do them within 1 minute. NOTE: You must re-register your original remote as part of this since it wipes out all old registrations.

    9) When done remove the jumper wire, paper clips, start the car, and with the money you saved go and fill up your fuel tank.
    if memory srves me correct this is right (mind u i used to use MUT to code them, and i think 3 keys max is all you can code
    project 380 w/shield washers complete yayaya

  5. #25
    380matey's Avatar
    Join Date
    Jul 2009
    Location
    New South Wales
    Posts
    1,001

    Default

    Does anyone know if you can get an encoded key from the locksmiths yet. Last time I checked (in March I think) they didnt have the program in the system yet.

  6. #26
    DOMO KUN!!!!!!!!!!!! Mecha-wombat's Avatar
    Join Date
    Jun 2009
    Location
    New South Wales
    Posts
    5,373

    Default

    I dont think MMAL has released it yet Matey

  7. #27
    380matey's Avatar
    Join Date
    Jul 2009
    Location
    New South Wales
    Posts
    1,001

    Default

    I checked again today and my local locksmith doesn't have the program yet. MMAL!!

  8. #28
    DOMO KUN!!!!!!!!!!!! Mecha-wombat's Avatar
    Join Date
    Jun 2009
    Location
    New South Wales
    Posts
    5,373

    Default

    4 keys max to be programmed to the car

  9. #29

    Join Date
    May 2011
    Location
    Western Australia
    Posts
    1

    Default

    Hi there,
    can someone please assist me with Remote issue?
    I would like to program the remote so when i unlock the doors, it will unlock all doors and not only the driver's door....

    thanks
    EldadiO

  10. #30
    isnt here anymore! Stormie's Avatar
    Join Date
    Sep 2007
    Location
    Western Australia
    Posts
    1,778

    Default

    dude do you have the multifunction screen? or a clock in your centre console. need a MF to make that change. if you take it to mitsu thats wht they'll do is plug one in, make the change and put back together.
    AMC//////My-380's-Roof-is-still-the-correct-colour division

+ Reply to Thread

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts